CLIO Fw

PRODUCT DESCRIPTION

The FW-01 Firewire Audio Interface sets new hardware precision standards for the CLIO System.
The FW-01 unit has been designed to be a complete two channels professional A/D D/A audio front-end for your PC; it is connected to the computer by an IEEE-1394 link giving you maximum performances; it can be powered by the same link giving you maximum portability.
The FW-01 performances (24 bit @ 192 kHz) represent state-of-the-art measurement capabilities for any audio device or acoustical test.
The FW-01 is equipped with an instrument grade balanced input and output analog circuitry with an exceptionally wide range of output attenuation and input gain that allows an easy interface to the outer world; the input and output loopback capability with the internal ultra stable voltage reference permit a simple and precise calibration of the whole instrument.
A switchable phantom power supply lets you directly connect an Audiomatica MIC-01, MIC-02 or MIC-03 as well as any other standard balanced microphone to any of the FW-01 input.

FW-01 TECHNICAL SPECIFICATIONS

GENERATOR
Two channels 24 Bit sigma-delta D/A Converter
Frequency range: 1Hz-90kHz
Frequency accuracy: >0.01%
Frequency resolution: 0.01Hz
Output impedance: 660Ohm
Max output level (Sine):17dBu (5.5Vrms)
Attenuation: 0.1 dB steps to full mute
THD+Noise(Sine):0.008%
Digital out: SPDIF

ANALYZER
Two channels 24 bit sigma-delta A/D Converter
Input range: +40 ÷ -40dBV
Max input acceptance: +40dBV (283Vpp)
Input impedance: 128kOhm (5.6kOhm mic)
Phantom power supply: 24V

PC SYSTEM RESOURCES
One free IEEE1394 port

CONNECT THE FW UNIT TO PC OR NOTEBOOK
To connect the FW-01 unit to your PC you need to do the following:
1) Locate an IEEE-1394 port on your PC. You may either use a standard 6-pin port (with
or without power supply) or a standard 4-pin (small connector, without power
supply) port.
2) If you use a 6-pin port use the supplied 6-pin-to-6-pin cable. If you use a 4-pin port
please provide an IEEE 1394 6-pin-to-4-pin cable (often referred as i-Link).
3) If you use a 6-pin port verify that it is capable of power supply.
4) If you use a 6-pin port without power supply or a 4-pin port you must also provide
a 12V external power supply.

MISCELLANEOUS
Sampling frequencies: 192kHz, 96kHz and 48kHz.
Audio connections: 2 XLR combo analog input, 2 XLR plus 2 RCA analog output, 1 RCA digital output
Digital connection: 6-pin IEEE1394
Power supply: IEEE1394 or 12V DC
Dimensions :16(w)x17(d)x4(h)
Weight: 0.8 kg




	PRODUCT DESCRIPTION The FW-01 Firewire Audio Interface sets new hardware precision standards for the CLIO System. The FW-01 unit has been designed to be a complete two channels professional A/D D/A audio front-end for your PC; it is connected to the computer by an IEEE-1394 link giving you maximum performances; it can be powered by the same link giving you maximum portability. The FW-01 performances (24 bit @ 192 kHz) represent state-of-the-art measurement capabilities for any audio device or acoustical test. The FW-01 is equipped with an instrument grade balanced input and output analog circuitry with an exceptionally wide range of output attenuation and input gain that allows an easy interface to the outer world; the input and output loopback capability with the internal ultra stable voltage reference permit a simple and precise calibration of the whole instrument. A switchable phantom power supply lets you directly connect an Audiomatica MIC-01, MIC-02 or MIC-03 as well as any other standard balanced microphone to any of the FW-01 input. FW-01 TECHNICAL SPECIFICATIONS GENERATOR Two channels 24 Bit sigma-delta D/A Converter Frequency range: 1Hz-90kHz Frequency accuracy: >0.01% Frequency resolution: 0.01Hz Output impedance: 660Ohm Max output level (Sine):17dBu (5.5Vrms) Attenuation: 0.1 dB steps to full mute THD+Noise(Sine):0.008% Digital out: SPDIF ANALYZER Two channels 24 bit sigma-delta A/D Converter Input range: +40 ÷ -40dBV Max input acceptance: +40dBV (283Vpp) Input impedance: 128kOhm (5.6kOhm mic) Phantom power supply: 24V PC SYSTEM RESOURCES One free IEEE1394 port CONNECT THE FW UNIT TO PC OR NOTEBOOK To connect the FW-01 unit to your PC you need to do the following: 1) Locate an IEEE-1394 port on your PC. You may either use a standard 6-pin port (with or without power supply) or a standard 4-pin (small connector, without power supply) port. 2) If you use a 6-pin port use the supplied 6-pin-to-6-pin cable. If you use a 4-pin port please provide an IEEE 1394 6-pin-to-4-pin cable (often referred as i-Link). 3) If you use a 6-pin port verify that it is capable of power supply. 4) If you use a 6-pin port without power supply or a 4-pin port you must also provide a 12V external power supply. MISCELLANEOUS Sampling frequencies: 192kHz, 96kHz and 48kHz. Audio connections: 2 XLR combo analog input, 2 XLR plus 2 RCA analog output, 1 RCA digital output Digital connection: 6-pin IEEE1394 Power supply: IEEE1394 or 12V DC Dimensions :16(w)x17(d)x4(h) Weight: 0.8 kg

	AVAILABLE SOFTWARE CLIO 10 system software for XP, Vista or Windows 7.